The Roll On Rock® Epoxy Flake Flooring System is an easy-to-install commercial epoxy floor coating that is applied over commercial concrete floors.
The Roll On Rock® Epoxy Flake Flooring kits include enough flake to broadcast them over the wet epoxy flooring to the point of rejection. This installation process allows the installer to throw the flake onto the wet epoxy flooring to the point where the floor is entirely covered up by the flake. The results look great every time because the installer scrapes off the loose flake, leaving a uniform blanket of flake on the entire concrete floor.
There are 50 lbs. of flake included in every two-car garage kit. That ratio is kept as the square footage increases, so every installation will look great, regardless of square footage. This system is designed to be easily installed by most commercial maintenance staff without the need for extensive training.
4195 Direct-to-Concrete Epoxy has been designed specifically for receiving the vinyl chips that are used to create the Roll On Rock® Commercial Epoxy Garage Flooring System. 4195 Epoxy wicks deep into the concrete floor and bonds so well that you can expect to get over eight pounds of MVE blocking power. That is due to the 4195 Epoxy flooring having up to three times more adhesion than other Epoxy floor and polyaspartic coatings. 4195 Epoxy provides plenty of time for the installer to apply the flake. The ideal chipping window is between 15 and 45 minutes of application.
The 5073 Polyurea Sealer is our most popular clear topcoat. It is recommended for use over the Roll On Rock® Epoxy Flake Flooring System. The water-clear, high-gloss, and high-build film of the 5073 Polyurea Sealer provides a beautiful, durable topcoat for flake flooring. This sealer is extremely scratch resistant and chemical resistant. The scratch resistance built into the clear topcoat will maintain its gloss longer than other concrete floor coating products.
5073 Polyurea Sealer is easy to apply by roller and brush, making it the ideal topcoat to use over epoxy flake installations. It also dries fast. In most cases, you can return the items to your garage several hours after the topcoat has been applied, and the car can be parked on it in a day or two. We offer a retarder that will extend the pot-life, making installation easy for new installers.
Use our optional 5205 Hybrid Ultra-Fast Drying Intermediate Coat when a luxurious, ultra-high build finish is desired. 5205 is a proprietary water-clear polyurea formula that is designed for easy installation and speed. It has a long pot-life up to 60 minutes in real world conditions, yet it dries in 30 minutes or less after it is applied over epoxy flake coatings.
Apply one coat of the 5205 over the epoxy flake after it has been scraped. This will seal the epoxy flake and be dry in about 30-60 minutes, allowing the installer to apply the second and final epoxy flooring topcoat.
This provides a higher build and finish since the 5073 Polyurea topcoat is applied directly to the surface of the 5205 coating. When used with 5073, a high-gloss, high-build floor finish can be achieved within hours, not days. 5073 is usually dry in two hours. It can be walked on soon after that or driven on the next day. Both our 5205 and our 5073 products are non-yellowing, so use over exterior surfaces will not be a problem.
The Roll On Rock® Epoxy Flake Flooring System can be accelerated so that it can be installed over a commercial concrete floor in one day. The accelerator causes the epoxy to dry to a hard state so the flake can be scraped in as little as two to three hours. We also offer UV packs that can be mixed with the 5073 Polyurea Sealer that will allow it to be installed outside. This will add many more years of UV exposure to its life.
Our Roll On Rock® Epoxy Flooring System products are ultra-low VOC coatings, and they are approved for use in the toughest AQMD districts in the United States and Canada. 5205 has 4 VOC, 4195 Epoxy has 13 VOC and 5073 Polyurea Sealer has 11 VOC.
The Roll On Rock® Epoxy Flake Flooring System is extremely chemical resistant and hot tire resistant. Hot tires will not stain the 5073 Polyurea Sealer topcoat used in the Roll On Rock® Epoxy Flake Flooring System. The following chemicals were shown to have no effect on 5073 in a chemical staining test: acetone, xylene, 10% HCL, ammonia, degreaser, Liquid Plummer®, vinegar, Clorox, Windex, motor oil, gasoline, Skydrol, and hot tire.
Features and Advantages: