An Extremely High Gloss Polyurea Coating Designed for Concrete Countertops
Versatile Building Products 5050 Polyurea Concrete Countertop Sealer is a proprietary formula that is designed for speed and Heat Resistance. New developments in Nano-Technology have allowed us to increase the heat resistance of this already Heat Resistant Polyurea. 5050 Polyurea Concrete Countertop Sealer has a potlife up to 45 minutes in real world conditions and it dries in 60-90 minutes after it is applied to concrete. 5050 will provide an extremely wet look to the concrete due to its ability to dive deep into the concrete surface
Features & Advantages
- NANO Technology Resists Heat
- Non YellowingUse Inside or Outside
- Extremely Fast Drying
- Long Pot-Life
- Penetrates Deep Into Porous Concrete
- Provides an extremely "Wet Look"
- Abrasion Resistant
- Will Cure At Temperatures Just Above Freezing
Install Guides
5050 Install Guide
Literature
Training Sign Up Form
M.S.D.S.
M.S.D.S 5050 Unit A | M.S.D.S 5050 Unit B
See our FAQ page for more tips
Our Polyurea beats Flexmar's Polyaspartic Coatings in an independent test reported on the Concrete Network!
See how our Polyurea Coatings Scored #1 with 100% and Flexmar's Polyaspartic scored 4th with 95%!
Polyurea 5073 and Polytop are identical accept for the fact that Polytop has additional Nano-Technology additives (very expensive stuff) to improve heat resistance, however this does not affect stain/solvent resistance at all. These are just some of the reasons why our Polyurea 5073 coating has risen to become the best clear topcoat out there for the garage floor coating customer.
When we set out to develop this Polyurea Concrete Coating Product Line, being good was not good enough, it had to be great. So don't be fooled by the hype that a product is great if it is a Polyaspartic, in most cases those are slick salesman talking! If you are looking for a 1 day garage floor system with better adhesion then Polyaspartic then be sure to try our Roll On Rock System 2® which can now be installed in 1 day and only two steps are needed. We were the first to bring a 2 step system to the garage floor coating market (at that time it was 4 steps & 4 days to do an install). We are repeating history again by bringing you a two step 1 day system!
The Results of CCI's Stain Tests
The Concrete Countertop Institute (CCI) performed extensive stain tests on 27 different sealers, which included multi-component catalyzed systems, single-component products, reactive sealers, penetrating treatments and wax.
Keep in mind that not all of the strengths and weaknesses of the sealers are quantified or addressed in CCI's sealer testing program. This was a test only of stain and etch resistance, so the ranking is not an indication of the overall desirability of a sealer. Other factors such as appearance, ease of application, cost, environmental impact and ease of repair were not tested. However, these factors are also important when choosing a sealer to use on your concrete countertops.
The best stain protection was provided by coatings, including waxes, hardeners and repellants. No penetrating sealer treatment provided anywhere near the protection than did an average-performing coating.
For coatings, the best stain protection was provided by highly chemical-resistant products such as urethanes and epoxies. On average, acrylics and reactive sealers faired poorly. The best acrylic performed about the same as the poorest performing epoxy.
It should be evident by the results that not all sealers provide the same degree of protection. It's up to you to decide how much protection is required for a particular application. Fireplace mantels and bathroom vanities, for example, have different performance requirements than kitchen countertops, so a sealer that would fair poorly in a kitchen might be fine on a bathroom vanity.
The top scoring multi-component finishes that provide excellent protection against all 14 staining agents:
| Sealer Name |
Score |
Acid |
Solvent |
Cleaner |
Harsh |
|
Polytop 5050
|
2 coats |
100% |
100% |
100% |
100% |
99% |
|
RJSC Stonelok
|
2 coats E3 + 1 coat 2K |
99% |
96% |
100% |
100% |
95% |
| RJSC Stonelok |
1 coat E3 + 1 coat 2K |
96% |
100% |
100% |
90% |
98% |
| Flexmar |
Satin polyaspartic, 2 coats |
95% |
97% |
88% |
100% |
95% |
Polytop and Flexmar are both solvent-based finishes. Richard James Specialty Chemical's Stonelok system uses a water-based epoxy (E3) and a water-based urethane (2K).
The above report was found on the ConcreteNetwork website.
|
Product Sitemap
800-535-3325
